Despite having amazing features, your Wavlink WiFi extender or repeater is also prone to technical issues. And, one of the most witnessed issues faced by a thousand users across the globe is the “Wavlink WiFi extender red light” issue. If you are also having the same issue, then this particular page is here to assist you.
Here, we have outlined the best troubleshooting hacks following which resolving the issue will be a walk in the park for you. Hence, read on!
Resolved: Wavlink WiFi Extender Red Light
Fix 1: Reboot Your Wavlink WiFi Extender
This is one of the most effective troubleshooting hacks tried by many users around the globe i.e. rebooting or power cycling the Wavlink extender. This is the easiest way to get rid of Wavlink extender technical-related issues. If you also want that the rebooting process helps you in a bigger way to fix the red light issue, just go through the instructions provided below:
-
Turn off your Wavlink WiFi range extender and also unplug it from its power outlet.
-
Wait for a few seconds.
-
Plug in your Wavlink extender back and also turn it on.
Fix 2: Check the Ethernet Connection
Have a quick nudge at the Ethernet cable connecting your Wavlink WiFi extender and your host router. There is a possibility that the cable you have used is worn out or damaged. Therefore, to troubleshoot the issue, it is recommended that you either replace the existing Ethernet cable with a new one or try connecting your Wavlink extender and router in a wireless manner.
Fix 3: Pull the Devices Closer
If your Wavlink WiFi extender and your host router are placed at a distance then you might get issues while connecting them via a wireless source, resulting in the red light issue. Thus, ensure to place your Wavlink extender and your existing device closer.
Fix 4: Perform Wavlink Firmware Update
Updating the firmware of your Wavlink WiFi extender can also help you troubleshoot the red light issue. Thus, for getting the issue fixed, it is advised you update the firmware of your Wavlink WiFi extender right away.
Fix 5: Reset Your Wavlink Extender
Even if after following all the above-mentioned troubleshooting hacks, you are still not able to fix the “Wavlink WiFi extender red light” issue? If yes, then it can be due to improper Wavlink repeater setup. Thus, to get the improper setup issue, consider resetting your Wavlink extender or repeater back to factory default values. Wondering how to reset the Wavlink extender? Wonder no more and apply the instructions outlined underneath.
How to Reset Wavlink Extender?
Here is how to reset your Wavlink WiFi range extender to the factory default values:
-
First things first, look for the reset hole on your Wavlink WiFi extender.
-
Once found, press it very carefully for a few seconds and release it.
Once you are done resetting your Wavlink WiFi extender, configure it from the scratch.
Thinking about how to reconfigure your Wavlink WiFi extender? Well, think no more because we are going to provide you with the easiest method to initiate and complete the Wavlink extender setup with ease.
Wavlink Extender Setup via WPS Method
-
Power on your Wavlink extender.
-
Wait for a few minutes after plugging in your Wavlink device.
-
Once the power LED on your Wavlink extender gets stable, head over to the next step.
-
Is the Wavlink extender’s power LED stable? If yes, then press the WPS button on it.
-
After pressing the Wavlink extender’s WPS button, remain calm. In simple words, wait for a couple of seconds.
-
Now, press the WPS button on your host router as well.
Once you have finished setting up your Wavlink extender using the WPS method, you can unplug the extender and plug it to the location of your choice. Bear in mind, the location you have selected for your Wavlink device must not be placed away from your host router.
To Sum Up
With that, our piece of writing on how to troubleshoot “Wavlink WiFi extender red light” issue ends here. We anticipate that after following the aforementioned tested and proven hacks, you are able to prevent yourself from seeing the red LED on your device. On the off chance, you see the red light again on your Wavlink extender, feel free to try the same hacks provided on this page.
